strassern
мое содержание
Все сообщения
Отзывы
Комментарии
ответы
Вопросы

Все сообщения

strassern 28/03/2018
These motors go! I have not had any issues with these motors.
BrotherHobby Returner R4 2205 2450KV 2700KV 4-5S Бесколлекторный мотор Для RC Дрон FPV Racing Multi Rotor
US$25.99 US$31.99
0
рекомендации
Комментарии (0)
strassern 28/03/2018
This is a 4 in 1 ESC solution that when combo'd with the Stack X F4 Flight Controller provide a very simple installation with less weight than many builds. Only 12 motor wires and a pos/neg battery connection make this board very simple to use for novice/entry level pilots.
Eachine Stack-X F4 Запасная часть Flytower 35A 4 В 1 ESC 2-6S BLHeli_S Dshot600 Готов для RC Дрон FPV Racing
US$41.99 US$50.99
7
рекомендации
Комментарии (0)
strassern 28/03/2018
This VTX antenna is designed for shorter visual transmission range but at the balance of much less weight than other more powerful antennas. It does what is expected of it and in the right conditions can go quite far. Nice and affordable. Happy Flying!
Запчасти башни Emax F4 Magnum 5.8G Дипольная волнообразная антенна
US$10.99 US$13.99
0
рекомендации
Комментарии (0)
strassern 28/03/2018
Very simple installation when paired with Stack-X 4 in 1 ESC unit and right now a lower cost than many other combination boards that include ESCs, FC, and VTX in one combo unit. The final result is only 2 36x36 boards and a reciever for a complete build of the "brains". This means less total soldering (and less weight) and could be helpful to entry level builders who have not perfected their soldering skills yet. There are some sets of pads that need to be addressed called bridges that activate particular settings such as how much voltage sent to the fpv camera and an sbus or ibus(etc used for you transmitter type) bridge. In my case the camera bridge is pre-soldered for 5v but the Sbus bridge needed to be addressed. Ensure you are using the correct amount of heat on your iron to ensure you do not accidentally remove the very small and delicate soldering pads. I would recommend 315-350 degrees Fahrenheit to address these bridges and if you are completely unfamiliar with soldering, please watch some videos and do some research to up your game before handling these bridges specifically. I know you want to get airborne but.....My best advice is DO NOT RUSH your build! As you hone your soldering skills, do your research, ask questions in forums if you need guidance, and don't be in too much of a hurry to get in the sky or you could make a mistake that will ensure you wait for 15-30 days to correct while new hardware ships. Happy Flying!
Eachine Stack-X F4 Flytower Запасная часть F4 Контроллер полета Встроенный OSD 40CH VTX Для FPV Гоночный РУ Дрон
US$31.59
4
рекомендации
Комментарии (1)
strassern 28/03/2018
The product arrived as a nice bright yellow color as the picture depicts. I have ordered other versions from other vendors in bulk and they were a light orange/yellow mix dull color. Happy Flying!
Штекер-разъем XT60 мужской-женский для аккумулятора Lipo RC Drone FPV Racing Multi Rotor
US$5.99 US$7.99
0
рекомендации
Комментарии (0)
strassern 28/03/2018
My only gripe is the exterior form factor. Of course, I assume there are a great deal of differences between different motor mounts and that was taken into account in my review. I personally used these with BrotherHobby Returner R4 2205 2450KV 2700KV motors. The exterior bulges up from the frame by a decent amount as the exterior flange pushes upward from the pressure. I did not like the look of so much material sticking up from the base of the motor. I have not enough experience to speak in relation to the reduction in noise but took the precautions of soft mounting motors and FC/stack. Ultimately this is a mostly unnoticeable unless taking stringent look at the quad up close. Happy Flying!
4 PCS 22XX Серия Мотор Силиконовый Антивибрационный Подушка для RC Дрона FPV Гонки Дрона
US$6.99 US$8.99
0
рекомендации
Комментарии (0)

Вы эксперт, можете ли вы помочь?

Мы искренне приглашаем вас подписаться на рассылку с ответом на приглашение!

Если вы подпишетесь, мы будем приглашать вас по электронной почте, чтобы ответить на вопросы людей о продуктах. Оформив подписку, вы также получите "Полезный значок "! Вы можете отказаться от подписки в любой момент на странице настроек конфиденциальности.

Помогайте другим и будьте счастливее!

  • Подписаться

О бейджах

Значки связаны с сообществом, и пользователи зарабатывают значки, создавая качественный контент, выполняя миссии или участвуя в специальных мероприятиях. У определенных людей также будет свой собственный эксклюзивный значок.
Значок генерального директора

Значок генерального директора принадлежит только начальнику Banggood.

Значки, которые вы можете заработать, скоро появятся
  • OK

About Badges

Badges are related to the community, and users earn badges by creating quality content, completing missions, or by participating in special activities.

Helpful Badges

The Badge is awarded to users who are subscribed to the Invite Answer email and signifies their gratitude to help others. The badge appearance upgrades as the user helps more people.
  • OK

Thank you for subscribing! You have also earned a badge!

  • View It

Thank you! Your answer will help ###name### and ###num### other people!

Check awaiting answers to see more people who need help.

  • OK

Thank you! Your answer will help ###name### and ###num### other people!

Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!

  • Subscribe

Are you ready to help?

We invite you to subscribe to our Invite Answer email!

Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.

  • Subscribe