ruthart
Q: how big is the diameter on the hole
Задавает BG782340512 на 2021-04-30 11:34:44
ruthart The hole is 5mm diameter.
2021-04-30 12:52:47 полезный (0)Q: Does this board have a programmer on board?
Задавает trypesdg на 2021-03-28 08:22:52
ruthart It has a boot loader. If you write a program in the Arduino IDE or PlatformIO you can upload it through the USB port.
2021-03-28 09:12:48 полезный (0)
Q: How bad is the backlash on these?
Задавает Bgsto на 2021-02-23 08:36:59
ruthart Backlash is undetectable. But keep in mind that there is a 64 times speed reduction gear inside so it is quite slow.
2021-02-24 07:05:03 полезный (1)Q: Will it work with tmc2208 stepper driver?
Задавает BG531791042 на 2021-02-16 12:49:09
ruthart Yes. Go to reprap.org and check out the wiki info for this board.
2021-02-16 01:50:29 полезный (0)Q: Is it suitable to be used for a DIY 3d printer?
Задавает R0203 на 2021-01-13 10:12:08
ruthart Yes, probably the best choice.
2021-01-13 11:21:26 полезный (0)Q: WHAT HOSE SIZE ARE THE INLET & OUTLET ???
Задавает BG171125920 на 2020-07-04 12:14:40
ruthart The thread is 0.5 inch pipe thread (od 20mm 14 threads per inch). the id is 12 - 13mm.The best fit is probably 0.5 inch hose.
2020-07-05 09:42:43 полезный (0)Q: What is the current draw of this magnet
Задавает BG161715491 на 2020-06-17 01:03:45
ruthart According to the specs 110mA.
2020-06-18 11:31:14 полезный (0)
ruthart Use a knife with a strong blade and pry it open at the corners. You have to apply some force but I was able to open it. The LED is next to the battery area.
2020-05-15 10:28:02 полезный (0)Q: What stepper motor will this work with?
Задавает ancsvc на 2020-05-06 01:21:20
ruthart Any nema 17 stepper will work. You don't need high torque.
2020-05-06 08:34:18 полезный (0)
Мы искренне приглашаем вас подписаться на рассылку с ответом на приглашение!
Если вы подпишетесь, мы будем приглашать вас по электронной почте, чтобы ответить на вопросы людей о продуктах. Оформив подписку, вы также получите "Полезный значок "! Вы можете отказаться от подписки в любой момент на странице настроек конфиденциальности.
Помогайте другим и будьте счастливее!
Thank you for subscribing! You have also earned a badge!
Thank you! Your answer will help ###name### and ###num### other people!
Check awaiting answers to see more people who need help.
Thank you! Your answer will help ###name### and ###num### other people!
Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!
We invite you to subscribe to our Invite Answer email!
Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.
ruthart It generates a signal which can be used by your main board if so equipped. It would stop the print, record the position and sound the alarm. You may have to modify the firmware for this to work.
2021-09-24 07:06:50 полезный (0)