danarrib
BG351738321 5V Best.
2022-02-08 01:02:20 полезный (0)
Q: Does this props needs to be balanced?
Задавает danarrib на 2019-10-23 10:04:19
antomolog у меня почти идеальные
2021-10-09 12:33:16 полезный (0)Q: كم بطارية استطيع وضعها في كل خلية
Задавает abuamroamaireh на 2021-02-05 05:52:03
danarrib You can wire in parallel as many as you want.
2021-08-04 12:44:34 полезный (2)
Q: I just wish that 7, 8 and 9 inch versions had 5mm or 6mm arm thickness instead of 4mm arms
Задавает danarrib на 2021-04-15 08:51:02
CutieePie You can change the arm.
2021-05-07 03:34:17 полезный (0)
tedhancock68 When I started making packs I thought I didn’t need any balancing at all since I was using new, Japanese cells and slow charging. Now, $300 in lost batteries has convinced me to permanently install one of these on every pack. It adds 50 - 100% to the cost of a pack, but very much worth it!
2020-12-23 10:37:51 полезный (0)
danarrib This board doesn't work AT ALL.
2021-03-14 12:08:02 полезный (1)Q: Does it work with iPhone 11 Pro Max?
Задавает danarrib на 2021-01-06 07:52:41
Apogee mxkmxk1 Yes, it does.
2021-02-05 06:11:51 полезный (0)Q: How can it be programmed? Where's the Instructions Manual?
Задавает danarrib на 2020-01-24 12:29:22
BG561117159 where can I find programming instructions please?
2020-09-01 11:29:05 полезный (0)Q: Can you please send a picture of the back side of this board?
Задавает danarrib на 2020-11-10 07:02:28
tedhancock68 You mean is there any components, traces, or electrical conductivity on the back? If that is your question then...no. It is well insulated on the back side with some rubbery coating and conformal.
2020-12-25 03:36:17 полезный (2)
danarrib@DrDuckFPV No, for 7 inch props I'm using 4S or 3S. 6S is too much for 7 inch on this motors.
Martin The XSR receiver inside could easily sent telemetry data to your transmitter. But I doubt most of the simulator softwares will transfer these data to the XSR.
2020-11-02 05:43:42 полезный (0)Q: What's the differente between T7056C and T7056C PRO version?
Задавает danarrib на 2019-11-26 02:23:58
BG114816400 The Pro version has more material on the connection point between hub and blade. The old ones were prone to explode when running 6S Low kv setups.
2020-10-29 01:48:47 полезный (0)Q: When the 1550kv version will be available?
Задавает danarrib на 2020-09-19 04:25:35
Hattiv Around Oct 26th
2020-10-09 06:03:22 полезный (1)Q: If it has a Barometer and I2C pads, would be PERFECT.
Задавает danarrib на 2020-08-08 11:28:40
BG454816422 According to the datasheet of STM32F722 LQFP64 and the HIFIONRC Betaflight unified target board definition, the MCU pins B10 and pin B11 (TX3,RX3 on solder pads) should be mappable to I2C device 2. No guarantees, but I'm going to attempt using that.Update: tried and it's working. I have a BMP280-3.3. VCC of baro is connected to the 3.3V PAD, SCL of baro is connected to TX3, SDA of baro is connected to RX3. Here are the betaflight configuration changes to make it work:resource SERIAL_TX 3 NONEresource SERIAL_RX 3 NONEresource I2C_SCL 2 B10resource I2C_SDA 2 B11set baro_bustype = I2Cset baro_i2c_device = 2set baro_i2c_address = 0set baro_hardware = AUTO
2020-10-06 05:30:11 полезный (2)Мы искренне приглашаем вас подписаться на рассылку с ответом на приглашение!
Если вы подпишетесь, мы будем приглашать вас по электронной почте, чтобы ответить на вопросы людей о продуктах. Оформив подписку, вы также получите "Полезный значок "! Вы можете отказаться от подписки в любой момент на странице настроек конфиденциальности.
Помогайте другим и будьте счастливее!
Thank you for subscribing! You have also earned a badge!
Thank you! Your answer will help ###name### and ###num### other people!
Check awaiting answers to see more people who need help.
Thank you! Your answer will help ###name### and ###num### other people!
Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!
We invite you to subscribe to our Invite Answer email!
Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.
JohnHutch they do...search
2022-07-31 10:11:32 полезный (0)