Garry
Q: I bought the ELRS 2.4GHz version, how can I bind the receiver and Transmitter?
Задавает Chan на 2023-06-08 04:11:51
Q: Does this work with the baby ape pro v2?
Задавает BG531323421 на 2023-07-05 08:21:52
Garry Yes, I have the same goggles and a baby ape. Work great.
2023-07-05 09:35:28 полезный (0)Q: How big heatsink do i need to cover mosfets?
Задавает Jakke235 на 2023-04-10 02:34:34
Garry I have used this product and I only have it in a 3D printed case. If you are going to use it for continuous welding you may want to check the temps. For spot welding small packs, mine does not heat up. Best Regards
2023-04-10 05:27:51 полезный (1)Q: I have a DJI mini SE I want to know how to hook goggles up to it or can I hook goggles up to it TY
Задавает BG114344404 на 2023-02-10 09:09:04
Garry Eachine EV800DM FPV goggles receive the A, B, E, F, and R channels. I believe DJI receives on the D and J frequency band. Maybe you can see if the DJI video transmitter is capable of transmitting in the "R" (race band) frequency range. If not, you can't use these FPV goggles. Best Ragards.
2023-02-10 10:07:30 полезный (0)Q: it use in flysky receiver, and how many use volts it in?
Задавает BG524817545 на 2022-01-13 06:36:26
Garry 30A ESC has a BEC: 2A, 5V (Linear mode). 40A ESC has a BEC:3A, 5V (Switching) This ESC provides 5V for your servos and receiver.
2022-03-28 06:56:31 полезный (0)Q: 1. what prop for a 3 cell battery. 2. how many mm do you need for the cabble?
Задавает BG421546025 на 2021-09-03 11:26:21
Garry Depends on the KVA rating of the motor; here is data from sheet included with motor: 1100 KVA - 2150g max pull, 911 watts, 70 A ESC, 3 cell 13x8, 5 cell 12x6 900 KVA - 1780g max pull, 770 watts, 70 A ESC, 3 cell 12x10, 5 cell 11x8.5 790 KVA - 1650g max pull, 717 watts, 70 A ESC, 3 cell 12x12, 5 cell 11x7 Motor comes with 3mm connectors installed. Regards
2021-09-03 12:02:45 полезный (0)
Garry Refer to the Matek website for the F-765. Scroll down until you see this text "F765-WING is discontinued due to STM32F765VIT6 shortage." There are several 'tabs' starting with "Gallery"; select the 4th tab "INav Wiring". It shows how to properly connect the GPS to the F-765. It shows Matek RX to GPS TX and Matek TX to GPS RX. Regards
2021-07-30 01:55:47 полезный (0)Q: Is this product as simple as: "Put one signal type in, get the other two signal types out"?
Задавает JackClayts на 2021-05-26 01:21:14
Garry Yes, Features: Input SBUS signal and output PWM and PPM signals simultaneously Input PWM signal and simultaneously output PPM and SBUS signals Input PPM signal and output PWM and SBUS signals simultaneously
2021-05-26 06:56:50 полезный (3)
Garry Yes, I received a cable with mine.
2021-02-01 04:35:21 полезный (1)
JayBee Your YouTube video (Kh2zizuSgF0) is not even the same product ???
2020-06-24 09:52:57 полезный (3)Q: does this work with 18650s?
Задавает Jamzz на 2020-12-25 06:23:14
Garry Yes, it comes with a 2 cell battery clip and wiring. I upgraded mine to with a LiIon 5000mah, 2 cell pack.
2020-12-26 11:29:23 полезный (0)Q: Hello sir this module I can directly use by 12 v battery?? and 9.000OMR ONLY sarkit or with war??
Задавает Mohsin Ali на 2020-10-13 03:46:27
Garry Mohsin, the kit comes with the XT-60 un-soldered, so you can use wire. Make sure you use a high capacity battery and add the capacitor across the input positive and negative terminals. It is designed for a 3 cell Lipo battery with at least 150 A output capability. I'm using a 3 cell Lipo, 3000mah and 60C rated battery which is 180A capable (very short duration).
2020-10-13 11:04:15 полезный (0)Q: what is the electrolytic cap for
Задавает ixdune@yahoo.com на 2020-03-21 09:03:15
Garry The yellow item is an XT-60 battery plug. It is NOT a capacitor! The battery plugs into the PCB yellow plug.
2020-05-16 10:38:34 полезный (0)
Garry - Four 10-bit ADC pin (analog) - 12 digital I / O (5 PWM capability, pins 3,5,6,9,10)
2018-11-02 08:44:45 полезный (0)Мы искренне приглашаем вас подписаться на рассылку с ответом на приглашение!
Если вы подпишетесь, мы будем приглашать вас по электронной почте, чтобы ответить на вопросы людей о продуктах. Оформив подписку, вы также получите "Полезный значок "! Вы можете отказаться от подписки в любой момент на странице настроек конфиденциальности.
Помогайте другим и будьте счастливее!
Thank you for subscribing! You have also earned a badge!
Thank you! Your answer will help ###name### and ###num### other people!
Check awaiting answers to see more people who need help.
Thank you! Your answer will help ###name### and ###num### other people!
Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!
We invite you to subscribe to our Invite Answer email!
Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.
Garry 1. You need a transmitter that is ELRS capable. The TX module is configured with a binding phrase. 2. Depending on the ELRS firmware version of the RX, you will probably want to update it to the latest. At that time, you configure the binding phrase in the RX firmware and upload it to the RX. 3. Power on the TX, then power on the RX. The RX should connect to the TX within a second or two. It is just that easy! Read how to configure ELRS transmitter modules and receivers. It is not hard to do. Best regards
2023-07-06 01:11:26 полезный (0)