It will not fit any frame since it's very large. But fits the MartianII :) be carefull with the boot button. mine broke off very easily.

It will not fit any frame since it's very large. But fits the MartianII :) be carefull with the boot button. mine broke off very easily.

It will not fit any frame since it's very large. But fits the MartianII :) be carefull with the boot button. mine broke off very easily.

The concept itself is great. The execution... could be a little better. Pros A good all in one - a lot of cables less. Well... actually only those from the receiver. Antennas are swappable thanks to the plugs on board. Ease of installation - set the ports go. Cons. IT IS LONG. A bit to long for most frames that I have. It does not fit my QAV 214 - camera supports are in the way. And whats worse back supports touch the ESC power connectors!!! You might have battery current on those !!!

The concept itself is great. The execution... could be a little better. Pros A good all in one - a lot of cables less. Well... actually only those from the receiver. Antennas are swappable thanks to the plugs on board. Ease of installation - set the ports go. Cons. IT IS LONG. A bit to long for most frames that I have. It does not fit my QAV 214 - camera supports are in the way. And whats worse back supports touch the ESC power connectors!!! You might have battery current on those !!!

The concept itself is great. The execution... could be a little better. Pros A good all in one - a lot of cables less. Well... actually only those from the receiver. Antennas are swappable thanks to the plugs on board. Ease of installation - set the ports go. Cons. IT IS LONG. A bit to long for most frames that I have. It does not fit my QAV 214 - camera supports are in the way. And whats worse back supports touch the ESC power connectors!!! You might have battery current on those !!!

This flight controller has an integrated XSR reveiver with smart port and sbus, a PDB with current sensor, accelerometer and gyro. The chip is the MPU6000, which is the better choice, because the MPU6050 is too sensitive to vibrations and thus less effective in compensating wind, max angles etc. You can directly connect up to a 6S lipo, and it has 6 pwm outputs for motor esc's and servo's. You can connect a led strip which is programmable, a buzzer, a video camera and a video transmitter. And yes, it has an On Screen Display which is fully adjustable with Betaflight configurator software, with which you can also update the firmware of the FC. it has a 5Volt supply and a VBat output. What I don't like : it has 6 built in UART's which is great, but the Betaflight configurator shows only 3 UART's, from which you only can use one. This is not a temporary error in soft- or firmware. The other two UART's have to be assigned, one to the receiver and one to the smartport. The only way to get more in/outputs is to configure 'softserial'. And that's getting very technical for many users. When you want to control the video camera and transmitter, get telemetry from the esc's and gps then this board is not for novice users. The board is too big for all tiny quads and for most medium size quads. The manual and technical spec is lacking, there is no info about the max current to the esc's the max current, from the 5V BEC supply, the max current for the current sensor, and which UART's are really free for use. What I like is that you don't need the inverter hack to make it work, the inverters are built in. Secondly it has a F4 cpu, so fast and smooth function. And third : a good price for all you're getting. And fourth, it is an all in one ; receiver, flight controller and power distribution board with current sensor.

This flight controller has an integrated XSR reveiver with smart port and sbus, a PDB with current sensor, accelerometer and gyro. The chip is the MPU6000, which is the better choice, because the MPU6050 is too sensitive to vibrations and thus less effective in compensating wind, max angles etc. You can directly connect up to a 6S lipo, and it has 6 pwm outputs for motor esc's and servo's. You can connect a led strip which is programmable, a buzzer, a video camera and a video transmitter. And yes, it has an On Screen Display which is fully adjustable with Betaflight configurator software, with which you can also update the firmware of the FC. it has a 5Volt supply and a VBat output. What I don't like : it has 6 built in UART's which is great, but the Betaflight configurator shows only 3 UART's, from which you only can use one. This is not a temporary error in soft- or firmware. The other two UART's have to be assigned, one to the receiver and one to the smartport. The only way to get more in/outputs is to configure 'softserial'. And that's getting very technical for many users. When you want to control the video camera and transmitter, get telemetry from the esc's and gps then this board is not for novice users. The board is too big for all tiny quads and for most medium size quads. The manual and technical spec is lacking, there is no info about the max current to the esc's the max current, from the 5V BEC supply, the max current for the current sensor, and which UART's are really free for use. What I like is that you don't need the inverter hack to make it work, the inverters are built in. Secondly it has a F4 cpu, so fast and smooth function. And third : a good price for all you're getting. And fourth, it is an all in one ; receiver, flight controller and power distribution board with current sensor.

This flight controller has an integrated XSR reveiver with smart port and sbus, a PDB with current sensor, accelerometer and gyro. The chip is the MPU6000, which is the better choice, because the MPU6050 is too sensitive to vibrations and thus less effective in compensating wind, max angles etc. You can directly connect up to a 6S lipo, and it has 6 pwm outputs for motor esc's and servo's. You can connect a led strip which is programmable, a buzzer, a video camera and a video transmitter. And yes, it has an On Screen Display which is fully adjustable with Betaflight configurator software, with which you can also update the firmware of the FC. it has a 5Volt supply and a VBat output. What I don't like : it has 6 built in UART's which is great, but the Betaflight configurator shows only 3 UART's, from which you only can use one. This is not a temporary error in soft- or firmware. The other two UART's have to be assigned, one to the receiver and one to the smartport. The only way to get more in/outputs is to configure 'softserial'. And that's getting very technical for many users. When you want to control the video camera and transmitter, get telemetry from the esc's and gps then this board is not for novice users. The board is too big for all tiny quads and for most medium size quads. The manual and technical spec is lacking, there is no info about the max current to the esc's the max current, from the 5V BEC supply, the max current for the current sensor, and which UART's are really free for use. What I like is that you don't need the inverter hack to make it work, the inverters are built in. Secondly it has a F4 cpu, so fast and smooth function. And third : a good price for all you're getting. And fourth, it is an all in one ; receiver, flight controller and power distribution board with current sensor.

Works well easy to set up and fits very well in armattan chameleon. Saves space by including rx and pdb.

Works well easy to set up and fits very well in armattan chameleon. Saves space by including rx and pdb.

Works well easy to set up and fits very well in armattan chameleon. Saves space by including rx and pdb.

Lovely all in one board for a clean good build. Set it up easily with my QX7 transmitter.

Lovely all in one board for a clean good build. Set it up easily with my QX7 transmitter.

Lovely all in one board for a clean good build. Set it up easily with my QX7 transmitter.

Perfect ALL in one board!

Perfect ALL in one board!

Perfect ALL in one board!

ca va etre ma seconde... j en suis tres content.

ca va etre ma seconde... j en suis tres content.

ca va etre ma seconde... j en suis tres content.

Esta placa ha sido sustituida sin ningún cargo porque la anterior viene defectuosa. Rápida respuesta. Genial.

Esta placa ha sido sustituida sin ningún cargo porque la anterior viene defectuosa. Rápida respuesta. Genial.

Esta placa ha sido sustituida sin ningún cargo porque la anterior viene defectuosa. Rápida respuesta. Genial.

3 in 1 product. beautiful circuit.... easy ton install thank you banggood !!!

3 in 1 product. beautiful circuit.... easy ton install thank you banggood !!!

3 in 1 product. beautiful circuit.... easy ton install thank you banggood !!!

fonctionne parfaitement et sans vibration. la livraison ok. je suis très content.

fonctionne parfaitement et sans vibration. la livraison ok. je suis très content.

fonctionne parfaitement et sans vibration. la livraison ok. je suis très content.