Отзывы покупателей

Написать отзыв
  • Все отзывы (111)
  • Образ (11)
  • Видео (1)
  • Все звезды
    • Все звезды(111)
    • 5 Звезда(105)
    • 4 Звезда(4)
    • 3 Звезда(1)
    • 2 Звезда(0)
    • 1 Звезда(1)
Сортировать по:
оценке
  • оценке
  • полезности
  • дате
Отзывы только из вашей страны (Russian Federation)
|
Показать оригинал

Часть обзора переведена автоматически.

  • 01/04/2016

    This is a 44E hall sensor. Simple to connect and use with Arduino/Genuino projects. The 3 connectors are GND (-), VCC 5v (in the middle without label) and signal. From testing this sensor it seems to be quite digital, so reading nearly high value when no magnetic field is close to the sensor, dropping to low (ground) when magnet is coming close to sensor (distance 10-12mm). Please note the sensor will only react to north of the magnet, so make sure to use it in the right direction. When magnetic field is strong enough, a small LED will light green and signal drop to low.

    Комментарии
    Показать оригинал
  • 02/09/2013

    Pros: Quite easy to figure out without any documentation, all the pins are either well-labeled or obvious. Good quality for the price.Also it is really small so it could be hidden if you wanted to. Cons: None that I can think of... Work right away and compatible with arduino, mbed and all kind of other mircocontroller boards. I don't have any cons till now and I can not think of any. Especially for this price!!! Other: Easy to interface to my Arduino, good deal. I will recommend this to friends.

    Комментарии
    Показать оригинал
  • 04/07/2016

    Bon produit. Livraison rapide.

    Комментарии
    Показать оригинал
  • 30/01/2019

    beau petit module, pas encore testé car magnétisme pas encore livrés

    Комментарии
    Показать оригинал
  • 29/12/2018

    Teşekkür ederim kullanacağım - 謝謝你我會用 - Thank you I will use

    Комментарии
    Показать оригинал
  • 26/08/2014

    I bought 3 of them to make probe for my 3d printer Their accuracy is correct and the repeatability is great ==> my first layer is always of 0.25mm. Just need a little bit of kapton or other tape to isolate the pads beneath the pins of the sensor

    Комментарии
    Показать оригинал
  • 19/09/2020

    Получено хорошо и в хорошем состоянии. Но сначала нужно проверить.

    Комментарии
    Показать оригинал
  • 08/09/2020

    Отлично, не могу дождаться, чтобы попробовать это

    Комментарии
    Показать оригинал
  • 13/03/2019

    parfait 👌

    Комментарии
    Показать оригинал
  • 25/03/2018

    Tested with 5v and it's working great. The sensor doesn't stand above the board as shown in the listing picture. I'm not sure if that'll matter to me or not.

    Комментарии
    Показать оригинал
Show:

    Общий 0 страницы

    Перейти на страницу

    Рекомендуем

    recommendation for you
    • US$9.49
    • US$9.99
    • US$12.43
    • US$6.69
    • US$13.81
    • US$7.99
    • US$11.99
    • US$6.99
    • US$8.99
    • US$19.99
    • US$4.99
    • US$4.99
    • US$4.99
    • US$4.99
    • US$10.99
    • US$8.99
    • US$8.99
    • US$5.99