AresFPV
Q: does this Rx work with low voltage servo? If the input vikty is 1S lipo (3.7v-4.2v)
Задавает KLKOK на 2018-09-12 01:18:40
AresFPV yes should work fine but as you said it will need a power input
2023-01-07 02:10:04 полезный (0)Q: Is this DSMX/DSM2 compatible?
Задавает gjadam1 на 2021-05-02 02:24:15
AresFPV no it is not. it uses the afhds 2a protocol
2023-01-07 02:09:24 полезный (0)Q: can this be used in EU (italy) ?
Задавает Yexel на 2018-01-04 06:58:52
AresFPV should be ok as its a 2.4ghz system
2023-01-07 02:06:36 полезный (0)Q: what is working distance between receiver and remote control
Задавает BG539185151 на 2021-11-18 02:20:28
AresFPV average around 400m maximum I expect
2022-11-05 11:46:34 полезный (0)Q: Can this be used in the uk? The nominal voltage here is 230v
Задавает BG564816174 на 2020-04-17 07:09:06
AresFPV yes the power supply is configured for 230v
2022-11-05 11:45:28 полезный (0)Q: can it get stuck at customs in India???
Задавает Chaitany на 2020-04-08 12:31:00
AresFPV not sure. may be best to contact BG directly
2022-07-22 04:19:28 полезный (0)Q: Can I use the bn-880 with that mount?
Задавает M0CKY на 2020-06-22 09:08:43
AresFPV I think the 880 is a bit too large, the antenna would not fit with the lip around the mount. it may be possible for it to fit with slight modification to the mount, but this gps module is just slightly larger
2022-07-22 04:18:45 полезный (0)
AresFPV you need to print a replacement z carriage, have a look at this one on thingiverse: thing:4803721
2022-07-05 04:17:49 полезный (0)Q: i have bond with my flysky fs i6 but the Signal com not i don't know why can you please help me
Задавает Mojaa на 2018-10-27 03:31:41
AresFPV it could be you have selected the wrong communication method, this should be pwm for this receiver, that or it did not bind correctly. having a correct binding should show the voltage of the receiver on the transmitters screen
2022-07-05 04:14:29 полезный (0)Q: does this have a receiver built into it?
Задавает Kevin на 2019-10-18 10:51:54
AresFPV no you will need one separately
2022-06-22 03:00:40 полезный (0)
AresFPV yes. i suggest using single flute endmill for ali
2022-06-22 03:00:05 полезный (0)Q: Can this Rx FS2A be binded with a Turnigy 9X V2 AFDHS2A ?
Задавает claudycharlier на 2020-12-05 10:03:08
AresFPV yes the 9xv2 with the afhds2a module will bind as the protocols are the same
2022-05-29 11:26:50 полезный (0)Q: Is there a wiring diagram available?
Задавает kechols_jr на 2020-04-22 03:19:04
AresFPV fairly simple to wire, power is positive to the fused side i believe, motor doesnt matter as the wires can easily be swapped if the motor spins the wrong way. switch is used to turn on or off the motor separately or through a control board.
2022-05-29 11:13:47 полезный (0)Q: How do I power up the unit? It is DC right? Difficult to find a DC power converter with 30 Volts
Задавает flowin_through на 2021-04-07 10:14:27
AresFPV the power supply is connected to mains AC. there is no earth connection, but you can add one to the motor and or the power supply for safety
2022-05-29 11:11:03 полезный (0)
AresFPV may be best contacting BG
2022-05-20 01:46:39 полезный (0)Q: It is for two-pole motor or for three-pole motor?
Задавает Pablo_Razo на 2019-11-14 04:01:58
AresFPV brushed esc, so brushed or two pole motor
2022-05-17 08:33:18 полезный (0)Q: Will it work with Turnigy TGY-i6?
Задавает russell на 2017-11-04 08:56:44
AresFPV yes as protocols match also should work with i6s
2022-05-17 08:32:43 полезный (0)Q: peux t'on l'alimenter en 6S?
Задавает pad на 2019-10-19 05:03:30
AresFPV works with 6s, you need a large 50v 1000uf capacitor, and you will have no issues
2022-04-28 02:59:54 полезный (0)Мы искренне приглашаем вас подписаться на рассылку с ответом на приглашение!
Если вы подпишетесь, мы будем приглашать вас по электронной почте, чтобы ответить на вопросы людей о продуктах. Оформив подписку, вы также получите "Полезный значок "! Вы можете отказаться от подписки в любой момент на странице настроек конфиденциальности.
Помогайте другим и будьте счастливее!
Thank you for subscribing! You have also earned a badge!
Thank you! Your answer will help ###name### and ###num### other people!
Check awaiting answers to see more people who need help.
Thank you! Your answer will help ###name### and ###num### other people!
Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!
We invite you to subscribe to our Invite Answer email!
Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.
