Все сообщения

Q: Does the connector include BOTH the male AND female parts of the connector?

Задавает Scott Hergott на 2023-01-06 12:53:52

The seller If you have questions, you can send an email for customer service help.

2023-01-06 07:33:49 полезный (0)
Оплатить
ответы (1)

mobilefrag not 100% sure of the max and min voltages, it does work with all of my surface rx's @5-6v 3rd channel is recommended. if you use channel 1, you'll need a splitter so this switch and your steering servo are both connected to the rx. once connected this way, full left turn followed by full right turn should activate, cycle throug modes, and deactivate this device.

2022-10-31 11:41:49 полезный (0)
Оплатить
ответы (1)
Scott Hergott 07/06/2022
It is a decent switch, and I like the way it connects. Pleaser Note, IT DOES NOT NEED TO BE CONNECTED TO CHANNEL THREE. It will work on any channel, it just requires two sweeps of the channel to trigger a state change. For most RC vehicles, it is convenient to put it on your throttle channel (typically 3rd channel when flying a plane with AETR radio setup). The throttle channel is likely the best channel to put the switch as most model (surface or boat or plane) can easily handle the throttle flicked twice during operation. (E.g. In a plane I can do this on the ground, but also find a time during the flight where I can flick the throttle twice and change the lights but not cause the plane to crash... if I put it on the rudder channel and tried this it would likely cause the plane to crash....DON'T DO THIS. You can also break out the center red wire and connect an additional ground wire to the input ground wire and then use a seperate battery to power the switched outputs. In this way, you will not be using your BEC power to power the outputs. This will not interfer with your BEC or receiver power, but be aware this switch is not OPTO isolated so if it were to catastrophically faily (very unlikel as, the switch's chips do have build in protection) you would then only have whatever protection your receiver has. Powering it with the modification above and using a seperate battery gives you more protection, but obviously this would alter your Current Sensor setup, if you don't know what I'm refering to then ignore this, if you do know what I mean, you don't need me to even tell you this... so ignore it...and why did I just type this if I just told all to ignore it.... I don't know, I hate typing more than doing reviews... I have asked if the limits for max - min of the switch... look in Q&A they may get added. Pending that I may try to identify the ICs and lookup the numbers...and then may post them here at some point when I feel like typing ...
0
рекомендации
Комментарии (0)

Q: peut on le connecter avec une télécommande non wltoys ?

Задавает chrissDbanggood на 2022-05-02 12:46:18

Scott Hergott Ifyou have a multiprotocol transmitter such as a Jumper or Radiomaster TX16s AND that can output the proper protocol. I do not know if these radios support the receivers particular protocol. These are great radios and I have had great success with them, BUT ONLY if I can identify the receiver prior to binding and know it is supported by the multiprotocol module Radio. It can be very hard to identify the correct protocol as very often a toy and hobby company will rebrand anothers receiver making it unknown and trying to bind an unknown receiver by trial and error for the 300 supported protocols is unrealistic.

2022-06-07 04:23:14 полезный (0)
Оплатить
ответы (1)

Q: What tube goeswith this item

Задавает Judithka69 на 2019-04-02 01:58:24

Scott Hergott Astandard 6" exhaust hose will fit. To securely lock into the threads, a standard portable AC exhause hose of PVC would be best. (you can get replacement exhaust hoses for portable AC units, but they can be fairly expensive) A 6" flexible exhaust hose for a clothes dryer will work, but most likely will need to be duct taped to the adapter. They come in aluminium and PVC, the aluminium is better, but costs more. Dryer exhaust hoses are typically less durable as they are often only attached once, then protected by being behind the dryer, but if the portable AC unit doesn't move much and if their are no kids or pets or packs of roving wildebeests trample them they will work, and they cost less and are typically longer. They do come in an insulated variety as well, this is excellent as heat from the AC unit will not heat up the room as it flows outside. General rules: Exhaust hoses from portable AC get quite warm (typically 110F or 45C) depending on how much the unit is working. Make sure the exhaust hose can take such temperatrures. Try to keep the exhaust hose straight and short by removing excess bends and shortening by collapsing unnecessary portions. (Dryer exhaust hoses may require cutting excess off, do leave yourself some extra incese you want to move or use the AC unit else where.) They do make exhaust hose wraps to insulate the AC exhaust pipes they go around the pipes and the two sides attach to each other by velcro. Or, if you are handy y

2022-06-07 04:09:41 полезный (0)
Оплатить
ответы (1)

Q: How do I put the receiver into bind mode?

Задавает Scott Hergott на 2021-01-20 02:28:22

Angiosperm how to take apart ans how to install

2021-02-05 04:22:40 полезный (0)
Оплатить
ответы (1)