Все сообщения

Q: can you tell the distance between 2 holes??

Задавает BG184456057 на 2020-10-27 12:58:36

Fish According to the dimensions drawn on the picture on the add, It 5.9cm.

2021-01-22 02:29:54 полезный (0)
Оплатить
ответы (1)

Q: Are these tools for a metal or wood lathe?

Задавает Ines Thomas на 2019-03-05 02:30:41

Fish Usedfor metal turning

2020-08-16 02:49:25 полезный (0)
Оплатить
ответы (8)

Fish Hi there, Mine came like the picture. Display, cable with plug and cable with pickup and a magnet.

2020-07-27 02:38:58 полезный (0)
Оплатить
ответы (2)

Fish Hi there, It is in fact a dead center. The center point does not move. The seller has made a mistake. This center is great for turning small items between centers. The cut away allows one to get the lathe tool up close to the center. Hope this helps

2020-07-27 02:36:54 полезный (0)
Оплатить
ответы (2)

Q: Is the connection to the mill B16?

Задавает Franky на 2018-01-04 05:20:55

Fish This is a collet block and not a collet chuck. used to index collet held items hex or square in a vice for example. For example, B16 is a chuck arbor taper code for the side where a chuck would go. MT3 or R8 is the taper on machines connection side. Collet blocks are not that type of chuck and arbor. Seller might have or be able to help

2020-07-13 08:58:11 полезный (0)
Оплатить
ответы (2)

Q: Does it come with the magnet?

Задавает Edmundo на 2019-10-14 11:36:02

Fish Mine did come with a magnet.

2020-07-13 08:54:09 полезный (0)
Оплатить
ответы (5)

Q: is that come on the box?

Задавает pghcosta на 2020-07-12 02:48:44

Fish Hithere, I comes in a cardboard box, packed in polystyrene and in a plastic bag. No fancy box. I made my own wooden storage box

2020-07-13 08:53:28 полезный (0)
Оплатить
ответы (1)

Q: Where can I find a drawing on how to wire this up?

Задавает vernmitch на 2019-04-16 04:44:01

Fish I found it on youtube. Have a look at O

2020-06-05 02:45:52 полезный (0)
Оплатить
ответы (2)

Fish Thewiring diagram on the back of the product is correctly illustrated. Dont think it matters but I coppied someone elses wiring from a picture on the site. I connected the coil unit with black at the top, Red next one down. Brown (live) next to the red and then Blue (Neutral) at the bottom. I wired it into a plug circuit on the board where i fitted it and added an on-off switch. Could also just wire a plug in and plug it in a normal plug. Hope this helps

2020-01-10 07:58:45 полезный (0)
Оплатить
ответы (1)

Fish Ihave found it does store the last recorded data but have not tested how long or played with the settings. Hope this helps but someone might be able to give a better answer than i

2020-01-10 07:45:35 полезный (1)
Оплатить
ответы (3)

Fish Hi There. You are correct. It does open in order to go around the cable and clips back closed.

2020-01-07 08:54:29 полезный (0)
Оплатить
ответы (2)