ответы

Q: Hi! Is there any way to add the board to platformio?

Задавает BG533932531 на 2022-04-28 02:27:23

DrMichael Yes; the plarformio support is steadily growing for rp 2040. The main challenges remaining concern integrated debugging. Google for "platformio" and "rpi2040" to find plenty of material on how to do it. Alternatively, go to registry[dot]platformio[dot]org[forwardslash]platforms[forwardslash]platformio[forwardslash]raspberrypi for the official documentation.

полезный (0)
Отправить
ответы (1)

Q: can be used with raspberry?

Задавает BG530201049 на 2022-04-20 09:32:13

DrMichael It's all 3.3V so it should be OK and a A quick Google reveals a few tutorials on how to do this, even a couple in microPython, although I'd suggest programming it in C or C++ if your skill set is up to it.

полезный (0)
Отправить
ответы (1)

Q: tiene manual ? de ser asi quisiera recibirlo

Задавает BG334912254 на 2022-03-18 22:21:24

DrMichael justGoogle "Ai-Thinker ESP-C3-12F-Kit" and download the PDF from the AI Thinker site.

полезный (0)
Отправить
ответы (2)

DrMichael Youneed a driver CH341SER.ZIP. The Manufacturer's site is http www.wch.cn. You can click in the upper right of the screen to translate to English. The site lets you download both drivers and a Datasheet,

полезный (0)
Отправить
ответы (4)

DrMichael I'm not sure what you mean by "TFTjQuery111306900136617515209_1646909312831", but I assume you are talking about a UNO or MEGA2560 from your use of the term shield. Interfacing LCD displays with an MCU is not for the fainthearted; Online forums are full of people trying and failing to interface them. First of all, I'm not an expert - I'm an electronics hobbyist and software professional (PhD Computer Science) . However, even Adafruit , who are specialists in this sort of thing, have a NT35510 driver that only "kinda works" and is limited to 16-bit mode only. Some general points: a) LCDs are generally 3.3V so make sure you are happy with level-shifting b) they usually work with SPI and use multiple modes [8-bit, 16-bit etc] so you should be happy with modifying the board by soldering on 0-ohm resistors AND adjusting software registers accordingly. c) It is very hard to get accurate and trustworthy datasheets. If all this is "gobbledegook" I'd suggest you don't buy this board. If it makes sense, I'd suggest you start by researching datasheets and libraries.

полезный (0)
Отправить
ответы (1)

Q: can you interface with an Arduino UNO?

Задавает Danimal на 2022-03-03 12:50:47

DrMichael Ithink the safest answer to give is No, or, at least, not without a massive amount of work. This is an HDMI monitor so first of all, you'd have to generate an HDMI signal from an Arduino. That's a major challenge! I'd suggest you look for an Arduino compatible touch-capable LCD. Note that almost all such LCDs are 3.3 volts, so you'll still need a level shifter.

полезный (0)
Отправить
ответы (1)

Q: Se puede usar con el arduino ide?

Задавает BG334912254 на 2022-02-17 07:23:06

DrMichael Yes,there is a quick start guide to setting up the Arduino IDE for this board on the "instructables" web site

полезный (0)
Отправить
ответы (1)