This motor appears very similar to a Hextronic motor sold by HK. It even has the same potential for failure as the HK Hextronic motor. The wire connection point or one of the winding wires will eventually break or short from movement near the back of the motor. The best way to prevent this is to disassemble the motor and remove both bearings. Use a piece of paper towel at both ends of the bearing tunnel to seal it up. Make up some 4 hour epoxy thinned about 20% to 30% with epoxy thinner. Use this thinned epoxy to dip the winding's until they are thoroughly coated and bonded together. Use some unthinned epoxy to prevent the three connection wires from moving between the heat shrink and motor winding's. Mechanically this makes the winding's more durable and electrically it improved heat dissipation. After the epoxy thoroughly cures, (24 hours) remove the paper towel plugs from both ends of the bearing tunnel and make sure that no epoxy entered the tunnel that will interfere with the re-installation of the bearings.

This motor appears very similar to a Hextronic motor sold by HK. It even has the same potential for failure as the HK Hextronic motor. The wire connection point or one of the winding wires will eventually break or short from movement near the back of the motor. The best way to prevent this is to disassemble the motor and remove both bearings. Use a piece of paper towel at both ends of the bearing tunnel to seal it up. Make up some 4 hour epoxy thinned about 20% to 30% with epoxy thinner. Use this thinned epoxy to dip the winding's until they are thoroughly coated and bonded together. Use some unthinned epoxy to prevent the three connection wires from moving between the heat shrink and motor winding's. Mechanically this makes the winding's more durable and electrically it improved heat dissipation. After the epoxy thoroughly cures, (24 hours) remove the paper towel plugs from both ends of the bearing tunnel and make sure that no epoxy entered the tunnel that will interfere with the re-installation of the bearings.

This motor appears very similar to a Hextronic motor sold by HK. It even has the same potential for failure as the HK Hextronic motor. The wire connection point or one of the winding wires will eventually break or short from movement near the back of the motor. The best way to prevent this is to disassemble the motor and remove both bearings. Use a piece of paper towel at both ends of the bearing tunnel to seal it up. Make up some 4 hour epoxy thinned about 20% to 30% with epoxy thinner. Use this thinned epoxy to dip the winding's until they are thoroughly coated and bonded together. Use some unthinned epoxy to prevent the three connection wires from moving between the heat shrink and motor winding's. Mechanically this makes the winding's more durable and electrically it improved heat dissipation. After the epoxy thoroughly cures, (24 hours) remove the paper towel plugs from both ends of the bearing tunnel and make sure that no epoxy entered the tunnel that will interfere with the re-installation of the bearings.

Articolo arrivato in sostituzione di uno difettoso. Tutto perfetto Grazie

Articolo arrivato in sostituzione di uno difettoso. Tutto perfetto Grazie

Articolo arrivato in sostituzione di uno difettoso. Tutto perfetto Grazie

получено в хорошем состоянии

received with good condition

получено в хорошем состоянии

Как описано выше

Just as described

Как описано выше

двигатель, как описано

motore come da descrizione

двигатель, как описано

Отлично

excellent

Отлично

Как и ожидалось, это была замена Phoenix 1600

As expected, this was a replacement for a Phoenix 1600

Как и ожидалось, это была замена Phoenix 1600

Мотор получил через 2 недели после заказа - очень быстрая поставка. Еще не проверено. Только упаковка была довольно бедной - только два тонких пластиковых пакета (ни пузырьковой фольги, ни так). Сп Я надеюсь, мотор будет в порядке и работает должным образом.

The motor received 2 weeks after ordering - very fast delivery. Not tested yet. Only packaging was quite poor - only two thin plastic bags (no bubble foil or so). Sp I trust the motor will be O.K. and working properly.

Мотор получил через 2 недели после заказа - очень быстрая поставка. Еще не проверено. Только упаковка была довольно бедной - только два тонких пластиковых пакета (ни пузырьковой фольги, ни так). Сп Я надеюсь, мотор будет в порядке и работает должным образом.

ОЧЕНЬ ХОРОШОЙ

VERY GOOD

ОЧЕНЬ ХОРОШОЙ

Прекрасно

ottimo

Прекрасно