Продукт как описание. Протестировано ОК работает как ожидалось. У меня был небольшой эмоциональный шок, когда я заметил явную деформацию металлической крышки модуля из-за какого-то острого предмета на ней. К счастью, модуль не был сломан. В последнее время многие заказы от этого продавца очень плохо упакованы с точки зрения защиты во время перевозки. Только антистатический мешок внутри бумажного конверта и внутри большего пластикового конверта. Существует нет пузырь фольги для защиты хрупких элементов внутри, например. и они могут быть легко повреждены при грубой обработке во время транспортировки. В краткосрочной перспективе эта процедура может сэкономить деньги для продавца, но это ловушка, потому что в долгосрочной перспективе клиенты начнут избегать покупать от этого продавца из-за высокой скорости мертвых по прибытии продуктов. Доска хорошего качества. Рекомендую.

Product as description. Tested ok working as expected. I had a little emotional shock when I noticed clearly deformation of module metal cover due to some sharp object on top of it. Fortunately the module oled screen was not broken. Lately many orders from this seller are very poor packed in terms of protection during transit. Only the antistatic bag inside a paper envelope and inside a bigger plastic envelope. There is no bubble foil to protect the fragile items inside eg. oled lcd and these can be easily damaged by the rough handling during transport. In short term this procedure can save money for seller but it is a trap because in long term the customers will start avoid to buy from this seller due to high rate of dead on arrival products. Good quality board. Recommend.

Продукт как описание. Протестировано ОК работает как ожидалось. У меня был небольшой эмоциональный шок, когда я заметил явную деформацию металлической крышки модуля из-за какого-то острого предмета на ней. К счастью, модуль не был сломан. В последнее время многие заказы от этого продавца очень плохо упакованы с точки зрения защиты во время перевозки. Только антистатический мешок внутри бумажного конверта и внутри большего пластикового конверта. Существует нет пузырь фольги для защиты хрупких элементов внутри, например. и они могут быть легко повреждены при грубой обработке во время транспортировки. В краткосрочной перспективе эта процедура может сэкономить деньги для продавца, но это ловушка, потому что в долгосрочной перспективе клиенты начнут избегать покупать от этого продавца из-за высокой скорости мертвых по прибытии продуктов. Доска хорошего качества. Рекомендую.

it has a revision 1 chip it only has space for unprotected 18650 batteries

it has a revision 1 chip it only has space for unprotected 18650 batteries

it has a revision 1 chip it only has space for unprotected 18650 batteries

After a long search I finally had all the information to create my own sketches. So far, everything works. The OLED display is glued to the board. The adhesive dissolves after a short time. Doesn't look good, but it's harmless. Also a warning to everyone: The USB plug is soldered without through-plating and detaches relatively easily from the board. I am not the first to whom this happens. With my first board it happened already with the third plugging in. It's a case for e-waste. The connector goes very tight and is barely able to cope with the forces. This is now my second board and I will take appropriate precautions to prevent this from happening again.

After a long search I finally had all the information to create my own sketches. So far, everything works. The OLED display is glued to the board. The adhesive dissolves after a short time. Doesn't look good, but it's harmless. Also a warning to everyone: The USB plug is soldered without through-plating and detaches relatively easily from the board. I am not the first to whom this happens. With my first board it happened already with the third plugging in. It's a case for e-waste. The connector goes very tight and is barely able to cope with the forces. This is now my second board and I will take appropriate precautions to prevent this from happening again.

After a long search I finally had all the information to create my own sketches. So far, everything works. The OLED display is glued to the board. The adhesive dissolves after a short time. Doesn't look good, but it's harmless. Also a warning to everyone: The USB plug is soldered without through-plating and detaches relatively easily from the board. I am not the first to whom this happens. With my first board it happened already with the third plugging in. It's a case for e-waste. The connector goes very tight and is barely able to cope with the forces. This is now my second board and I will take appropriate precautions to prevent this from happening again.

The unit is tidy, but perhaps a little larger than I was expecting, the measurements on pictures are accurate though. I took note of previous comments and have applied a couple of drops of superglue to the USB connector to stop it snapping off. I have used a 4x18650 battery pack which should allow this to run for ages, so far I have only run the demo The OLED display looks white, but shows up blue in the photograph. Be aware that the standard 0,1" DuPont style headers supplied with the unit will NOT connect to a breadboard if soldered to the underside because of the depth of the battery holder - you would to use female to male extenders - you could always solder them to the top, but you wouldn't see the OLED I intend to use this without the headers, so it doesn't make any difference to me

The unit is tidy, but perhaps a little larger than I was expecting, the measurements on pictures are accurate though. I took note of previous comments and have applied a couple of drops of superglue to the USB connector to stop it snapping off. I have used a 4x18650 battery pack which should allow this to run for ages, so far I have only run the demo The OLED display looks white, but shows up blue in the photograph. Be aware that the standard 0,1" DuPont style headers supplied with the unit will NOT connect to a breadboard if soldered to the underside because of the depth of the battery holder - you would to use female to male extenders - you could always solder them to the top, but you wouldn't see the OLED I intend to use this without the headers, so it doesn't make any difference to me

The unit is tidy, but perhaps a little larger than I was expecting, the measurements on pictures are accurate though. I took note of previous comments and have applied a couple of drops of superglue to the USB connector to stop it snapping off. I have used a 4x18650 battery pack which should allow this to run for ages, so far I have only run the demo The OLED display looks white, but shows up blue in the photograph. Be aware that the standard 0,1" DuPont style headers supplied with the unit will NOT connect to a breadboard if soldered to the underside because of the depth of the battery holder - you would to use female to male extenders - you could always solder them to the top, but you wouldn't see the OLED I intend to use this without the headers, so it doesn't make any difference to me

board is working and looking great

board is working and looking great

board is working and looking great

Good product. Recommended.

Good product. Recommended.

Good product. Recommended.

У меня есть модуль для вращающихся светодиодных часов. Экран ПОВ. Этот модуль включает в себя WIFI, поэтому он обновляет часы из Интернета, и мне никогда не нужно вносить коррективы между летним и зимним временем. И мне не нужно исправлять время. Это место для батареи на модуле.

I got my module for rotating LED watch. POV screen. This module include WIFI so he update the watch from internet and I never need to make adjustments between summertime and wintertime. And I do not need to correct the time. It is place for battery on the module.

У меня есть модуль для вращающихся светодиодных часов. Экран ПОВ. Этот модуль включает в себя WIFI, поэтому он обновляет часы из Интернета, и мне никогда не нужно вносить коррективы между летним и зимним временем. И мне не нужно исправлять время. Это место для батареи на модуле.

не официальный продукт лилиго, а на основе официальной схемы (не имеет логотипа TTGO). Он работает как обаяние. Это старая модель. Новая модель называется Lilygo ttgo t18. Программное обеспечение и примеры на GitHub и над простым исследованием Google. (используйте следующие ключевые слова: ttgo oled и держатель батареи). очень рекомендуется, так как он поставляется из Великобритании. Имейте в виду, что вес батареи заставляет его упасть и тормоз USB разъем, если кабель подключен

not an official lilygo product but based on the official schematic (it has no ttgo logo). it works like a charm tho. this is the old model. the new model is called lilygo ttgo t18. software & examples are on GitHub and over a simple Google research. (use the following keywords: ttgo oled and battery holder). highly recommended as it is shipped from the UK. be aware that the weight of the battery makes it subject to fall and brake the usb connector if a cable is connected

не официальный продукт лилиго, а на основе официальной схемы (не имеет логотипа TTGO). Он работает как обаяние. Это старая модель. Новая модель называется Lilygo ttgo t18. Программное обеспечение и примеры на GitHub и над простым исследованием Google. (используйте следующие ключевые слова: ttgo oled и держатель батареи). очень рекомендуется, так как он поставляется из Великобритании. Имейте в виду, что вес батареи заставляет его упасть и тормоз USB разъем, если кабель подключен

la confezione non ha molte protezioni, ma non avendo i pin montati l'articolo non presenta danni. arriva con preinstallato uno scatck per il test del display. ho testato anche la batteria e funziona.

la confezione non ha molte protezioni, ma non avendo i pin montati l'articolo non presenta danni. arriva con preinstallato uno scatck per il test del display. ho testato anche la batteria e funziona.

la confezione non ha molte protezioni, ma non avendo i pin montati l'articolo non presenta danni. arriva con preinstallato uno scatck per il test del display. ho testato anche la batteria e funziona.

Very good ESP32 board. The built in OLED display is very easy to read. Bright enought. The Battery charger working fine. Recommended to buy together with a good 18650 battery.

Very good ESP32 board. The built in OLED display is very easy to read. Bright enought. The Battery charger working fine. Recommended to buy together with a good 18650 battery.

Very good ESP32 board. The built in OLED display is very easy to read. Bright enought. The Battery charger working fine. Recommended to buy together with a good 18650 battery.