Отзывы покупателей

Написать отзыв
  • Все отзывы (364)
  • Образ (41)
  • Видео (1)
  • Все звезды
    • Все звезды(364)
    • 5 Звезда(354)
    • 4 Звезда(7)
    • 3 Звезда(2)
    • 2 Звезда(0)
    • 1 Звезда(1)
Сортировать по:
оценке
  • оценке
  • полезности
  • дате
Отзывы только из вашей страны (Russian Federation)
|
Показать оригинал

Часть обзора переведена автоматически.

  • 03/04/2014

    I used this with a Microchip PIC development board to interface to a 20x4 LCD display. With only 4 wires (including 2 for power) it's simple to set up and uses far fewer ports than the standard LCD parallel interface. As delivered the address pads A0 A1 and A2 are open but pulled high - so the I2C address is 0x4E. Ports P7,P6,P5,P4 of the PCF8574 interface to DB7,DB6,DB5,DB4 of the LCD Display. Port P3 is hard-wired to the backlight via a transistor: 1 = on / 0 = off. It's great that the backlight can be switched on and off via software with no additional hardware required. Port P2 is the display bit clock : E = 1 -> E = 0 active. Port P1 is R/W hardware Read/Write bit hardware : Read = 1 / Write = 0, so reading from the LCD display is possible, if required. Port P0 is RS Register Select : CmdReg = 0 / DataReg = 1. Display driver is HD44780 compliant. A great buy! I won't be interfacing to an LCD in future without it.

    Комментарии
    Показать оригинал
  • 16/05/2015

    I bought some of these and found out that there are different models which need different pin configurations. Here is a beginners guide for the ones from Bangood: http://safe-power.appspot.com/i2c-en.html You need to download one library, and you are ready to enjoy LCDs on your arduino with only 2 Arduino pins occupied (plus GND and VCC). This little board saves you time and pins :-)

    Комментарии
    Показать оригинал
  • 18/01/2019

    Good quality.

    Комментарии
    Показать оригинал
  • 14/02/2021

    Успешно поставляется в Марокко и с хорошим качеством упаковки

    Комментарии
    Показать оригинал
  • 09/04/2021

    nice product. its really helpful to reduce the pins needed on a lcd. cool to see that there is a jumper include to enable or disable the onboard led. can be helpful in low power situations. the product was not damaged in shipping and the quality looks great!

    Комментарии
    Показать оригинал
  • 11/09/2020

    Получены хорошо в хорошем состоянии и хорошо упакованы. Все еще нужно проверить их

    Комментарии
    Показать оригинал
  • 27/02/2017

    The I2C interface module works fine on my blue 1602 LCD module. The I2C address is 0x27 out of the box so remember to modify your code accordingly. There is a very clear description that can be found here: http://arduino-info.wikispaces.com/LCD-Blue-I2C. It clearly describes the different available versions of the I2C interface. The one I received was version 3. When I first connected it and run the sample code I adjusted for the 16x2 display it did not seem to show any information on the display. The root cause was the potentiometer on the I2C interface not to be setup correctly out of the box. I needed to adjust it to change the contrast and show the characters on the screen. So I am happy with this interface as it reduces the connection to only 4 wires (2 for the power supply and 2 for the communication).

    Комментарии
    Показать оригинал
  • 20/08/2013

    After receiving item, I test it with good results. Runs fine.

    Комментарии
    Показать оригинал
  • 08/07/2020

    Сработало с первой попытки. Обратите внимание, чтобы установить соответствующим контраст на триммер: записи на дисплее могут показаться настолько тусклыми, чтобы заставить вас думать, что это не работает. Я поискал адрес сканером I2C (код, который легко найти на сайте Ардуино) и нашел мой предмет 0x27. Для изменения адреса необходимо установить перемычки припоя на точках A0-A1-A2 рядом с триммером. Сработал с первым выстрелом. Будьте осторожны, чтобы настроить контраст с триммером, потому что буквы на дисплее могут быть настолько непонятными, что, кажется, она не работает. Обнаружен адрес с помощью сканера I2C (его легко найти на сайте Arduino) в моем образце был 0x27. Для изменения адреса необходимо сварить перемычки на площадках A0-A1-A2 рядом с триммером.

    Комментарии
    Показать оригинал
  • 19/10/2018

    nice package

    Комментарии
    Показать оригинал
Show:

    Общий 0 страницы

    Перейти на страницу

    Рекомендуем

    recommendation for you
    • US$14.99
    • US$9.99
    • US$8.29
    • US$9.99
    • US$6.99
    • US$5.99
    • US$12.99
    • US$8.49
    • US$4.99
    • US$7.99
    • US$5.99
    • US$6.99
    • US$6.99
    • US$3.99
    • US$3.99
    • US$19.99
    • US$12.99
    • US$57.59