Review: HF Ferrite Core RF Choke / Noise Filter This ferrite core RF choke presents a solid solution for amateur radio operators looking to reduce interference and improve signal stability across HF bands. Built around a Ni-Zn ferrite core with a practical 50mm outer diameter (30mm inner), it strikes a good balance between size and performance, making it suitable for both portable and fixed station setups. One of its standout features is the wide frequency coverage from 1.8MHz to 50MHz, which ensures compatibility with nearly all common HF amateur bands. Whether you're operating on lower bands like 160m or pushing higher into 6m, this unit remains effective without requiring multiple filters. Performance-wise, it’s clearly designed with modern digital modes in mind. In modes such as FT8, JS8, and WSPR—where clean signals and low noise floors are critical—it does a commendable job suppressing common-mode interference. Users experiencing issues like USB dropouts, erratic software behavior, or RF feedback into equipment should notice a tangible improvement. The power handling is another strong point. With 350W for standard operation and up to 550W continuous (850W peak), it comfortably supports most amateur radio setups, including higher-power stations. This makes it versatile enough for both casual operators and more demanding users. Construction quality also deserves praise. The use of Ni-Zn ferrite ensures good high-frequency suppression, while the RG58 coaxial cable provides flexibility without being overly fragile. The pure copper soldered connectors add to overall reliability, suggesting this is built for long-term use rather than being a disposable accessory. On the downside, RG58—while flexible—is not the lowest-loss coax available, so extremely performance-focused users might prefer higher-grade cable in certain setups. Additionally, while the unit is effective, results will still depend on proper placement within the station. Overall Verdict: A reliable, well

Review: HF Ferrite Core RF Choke / Noise Filter This ferrite core RF choke presents a solid solution for amateur radio operators looking to reduce interference and improve signal stability across HF bands. Built around a Ni-Zn ferrite core with a practical 50mm outer diameter (30mm inner), it strikes a good balance between size and performance, making it suitable for both portable and fixed station setups. One of its standout features is the wide frequency coverage from 1.8MHz to 50MHz, which ensures compatibility with nearly all common HF amateur bands. Whether you're operating on lower bands like 160m or pushing higher into 6m, this unit remains effective without requiring multiple filters. Performance-wise, it’s clearly designed with modern digital modes in mind. In modes such as FT8, JS8, and WSPR—where clean signals and low noise floors are critical—it does a commendable job suppressing common-mode interference. Users experiencing issues like USB dropouts, erratic software behavior, or RF feedback into equipment should notice a tangible improvement. The power handling is another strong point. With 350W for standard operation and up to 550W continuous (850W peak), it comfortably supports most amateur radio setups, including higher-power stations. This makes it versatile enough for both casual operators and more demanding users. Construction quality also deserves praise. The use of Ni-Zn ferrite ensures good high-frequency suppression, while the RG58 coaxial cable provides flexibility without being overly fragile. The pure copper soldered connectors add to overall reliability, suggesting this is built for long-term use rather than being a disposable accessory. On the downside, RG58—while flexible—is not the lowest-loss coax available, so extremely performance-focused users might prefer higher-grade cable in certain setups. Additionally, while the unit is effective, results will still depend on proper placement within the station. Overall Verdict: A reliable, well

Review: HF Ferrite Core RF Choke / Noise Filter This ferrite core RF choke presents a solid solution for amateur radio operators looking to reduce interference and improve signal stability across HF bands. Built around a Ni-Zn ferrite core with a practical 50mm outer diameter (30mm inner), it strikes a good balance between size and performance, making it suitable for both portable and fixed station setups. One of its standout features is the wide frequency coverage from 1.8MHz to 50MHz, which ensures compatibility with nearly all common HF amateur bands. Whether you're operating on lower bands like 160m or pushing higher into 6m, this unit remains effective without requiring multiple filters. Performance-wise, it’s clearly designed with modern digital modes in mind. In modes such as FT8, JS8, and WSPR—where clean signals and low noise floors are critical—it does a commendable job suppressing common-mode interference. Users experiencing issues like USB dropouts, erratic software behavior, or RF feedback into equipment should notice a tangible improvement. The power handling is another strong point. With 350W for standard operation and up to 550W continuous (850W peak), it comfortably supports most amateur radio setups, including higher-power stations. This makes it versatile enough for both casual operators and more demanding users. Construction quality also deserves praise. The use of Ni-Zn ferrite ensures good high-frequency suppression, while the RG58 coaxial cable provides flexibility without being overly fragile. The pure copper soldered connectors add to overall reliability, suggesting this is built for long-term use rather than being a disposable accessory. On the downside, RG58—while flexible—is not the lowest-loss coax available, so extremely performance-focused users might prefer higher-grade cable in certain setups. Additionally, while the unit is effective, results will still depend on proper placement within the station. Overall Verdict: A reliable, well

Он сделан с качественными разъемами, но коаксиальный кабель RG58 подключен только к центральной жиле, а не к оплетке. Мне нужно сделать соединения оплетки!

It is made with a good quality connectors, but the RG58 cable are only connnected by midle center pin, not the braid of coax cable. I have to made the conections of the braid!

Он сделан с качественными разъемами, но коаксиальный кабель RG58 подключен только к центральной жиле, а не к оплетке. Мне нужно сделать соединения оплетки!