good product , little amount of outage in collets is disappointing

good product , little amount of outage in collets is disappointing

good product , little amount of outage in collets is disappointing

These ER11 collets are working fine for small CNC routers. Each collets comes in with a plastic yellow case. I tried a few out with various bits, and they all work very well.

These ER11 collets are working fine for small CNC routers. Each collets comes in with a plastic yellow case. I tried a few out with various bits, and they all work very well.

These ER11 collets are working fine for small CNC routers. Each collets comes in with a plastic yellow case. I tried a few out with various bits, and they all work very well.

Arrived today. Material is quite strong. Was packed nicely. But the quality is just average. I used the 3mm collet and my drill bit just doesnt fit straight. It wobbles. Once the collet is inserted, it takes a little bit of an effort to tighten the nut on the holder. I bought it for using with the RS775 motor. The shaft is a good fit, though it will need a little bit of hammering and as the listing suggests - heat before inserting. But it is a tight fit, so no problem. I will recommend this for hobbyists, but probably not for professionals.

Arrived today. Material is quite strong. Was packed nicely. But the quality is just average. I used the 3mm collet and my drill bit just doesnt fit straight. It wobbles. Once the collet is inserted, it takes a little bit of an effort to tighten the nut on the holder. I bought it for using with the RS775 motor. The shaft is a good fit, though it will need a little bit of hammering and as the listing suggests - heat before inserting. But it is a tight fit, so no problem. I will recommend this for hobbyists, but probably not for professionals.

Arrived today. Material is quite strong. Was packed nicely. But the quality is just average. I used the 3mm collet and my drill bit just doesnt fit straight. It wobbles. Once the collet is inserted, it takes a little bit of an effort to tighten the nut on the holder. I bought it for using with the RS775 motor. The shaft is a good fit, though it will need a little bit of hammering and as the listing suggests - heat before inserting. But it is a tight fit, so no problem. I will recommend this for hobbyists, but probably not for professionals.

Прибыли довольно быстро, за 2,5 недели, на вид качественные, в работе ещё не пробовал.

Прибыли довольно быстро, за 2,5 недели, на вид качественные, в работе ещё не пробовал.

Прибыли довольно быстро, за 2,5 недели, на вид качественные, в работе ещё не пробовал.

working good

working good

working good

Collet holder has very smooth running. Only the 1mm Collet does not fit in the Collet nut and the 1 mm hole is not in the middle.

Collet holder has very smooth running. Only the 1mm Collet does not fit in the Collet nut and the 1 mm hole is not in the middle.

Collet holder has very smooth running. Only the 1mm Collet does not fit in the Collet nut and the 1 mm hole is not in the middle.

qood quality

qood quality

qood quality

Very good build quality. Reguires some light re-bore to press fit on a 5 mm shaft

Very good build quality. Reguires some light re-bore to press fit on a 5 mm shaft

Very good build quality. Reguires some light re-bore to press fit on a 5 mm shaft

Все в порядке, все в порядке. Высокая удовлетворенность, а также качество. Продавец = *****!

It's okay it's OK. High satisfaction and also quality. Seller = *****!

Все в порядке, все в порядке. Высокая удовлетворенность, а также качество. Продавец = *****!

Looks like good. Not try yet. :)

Looks like good. Not try yet. :)

Looks like good. Not try yet. :)