Отзывы покупателей

4.74 из 5
Написать отзыв
  • Все отзывы (27)
  • Образ (3)
  • Видео (0)
  • Все звезды
    • Все звезды(27)
    • 5 Звезда(24)
    • 4 Звезда(1)
    • 3 Звезда(1)
    • 2 Звезда(0)
    • 1 Звезда(1)
Сортировать по:
оценке
  • оценке
  • полезности
  • дате
Отзывы только из вашей страны (Armenia)
  • November-24 2020 10:17:28

    All outer diameter are very precise but inner cone has an runout-off error of 0.14mm.

    Комментарии
  • July-06 2019 07:23:27

    looks good, arrived fast

    Комментарии
  • November-06 2017 06:35:25

    Mandrino ER11 di ottima qualità

    Комментарии
  • June-05 2020 03:37:02

    Firstly, the spindle arrived in good time. I bought a couple of these from different vendors to compare the quality. This one is the slightly more expensive of the two, but still very cheap. On first look I notice that the nut thread is rough. I have done quite a bit of threading on an industrial scale and can see immediately on this one I received the threads are tearing along the apex; before they get to this state the threading cutters should be changed for new ones. Having said that, the nut

    Комментарии
  • June-06 2020 02:11:33

    habs eingekürzt für makita läuft super

    Комментарии
  • February-21 2020 22:49:30

    Good chuck!

    Комментарии
  • February-11 2020 16:48:05

    How cheap!!!!?

    Комментарии
  • January-05 2016 16:02:11

    Chuck was described as 'high precision' but turned out to be 0.01mm accuracy, a nice surprise. External finish looks quite good. After opening my chuck, I found that the inside was serious corroded, resulting in no precision more at all. :-( Hopefully this was an incident, due to wrong application of protecting oil. Refund was made without any problem. Good service. :-) I have high expectations about the new chuck, because the description now even promisses an accuracy of 0.003!

    Комментарии
  • December-30 2015 11:02:42

    Думал, что Китайские валы, будут не очень. Однако, под микрометр всё промерил, вал действительно 10.00 на всей длине, посадка в подшипник будет плотная. Балансировку не проверял, но цанга думаю выдержит без биения 25-30 тысяч оборотов в минут. В общем вал мне понравился, буду делать

    Комментарии
  • January-16 2018 08:13:19

    Diameter of Shank is not 10mm, but 10.08mm - 10.19mm. He can not fit in Ball Bearings It must be further processed at 10mm But for the price, I think it's okay

    Комментарии (1)
Show:

    Total 0 pages

    Go to page

    Go

    Рекомендуем

    recommendation for you
    • US$11.40
    • US$2.84
    • US$6.12
    • US$7.05
    • US$3.78
    • US$3.29
    • US$9.89
    • US$5.66
    • US$3.99
    • US$36.69
    • US$6.99
    • US$4.99
    • US$5.99
    • US$10.90
    • US$2.99
    • US$5.99
    • US$3.99
    • US$5.99