Отзывы покупателей

Написать отзыв
  • Все отзывы (53)
  • Образ (6)
  • Видео (0)
  • Все звезды
    • Все звезды(53)
    • 5 Звезда(52)
    • 4 Звезда(1)
    • 3 Звезда(0)
    • 2 Звезда(0)
    • 1 Звезда(0)
Сортировать по:
оценке
  • оценке
  • полезности
  • дате
Отзывы только из вашей страны (Armenia)
|
Показать оригинал

Часть обзора переведена автоматически.

  • 14/03/2019

    De acordo com o anúncio

    Комментарии
    Показать оригинал
  • 10/06/2016

    Качество как обычно хорошее. Программаторы работают.

    Комментарии
    Показать оригинал
  • 19/05/2016

    USB to TTL serial adapter works very well and is very small. It is perfect for use with an Arduino Pro Mini. It works with Windows 10 .

    Комментарии
    Показать оригинал
  • 24/10/2016

    Testé avec module GPS GY-neo6mv2. Fonctionne correctement.

    Комментарии
    Показать оригинал
  • 12/03/2019

    high quality at low price.

    Комментарии
    Показать оригинал
  • 30/01/2017

    Товар качественный, получил за 2 недели.

    Комментарии
    Показать оригинал
  • 17/01/2021

    хороший продукт

    Комментарии
    Показать оригинал
  • 13/01/2021

    продукт хорошего качества.

    Комментарии
    Показать оригинал
  • 28/08/2016

    I tested 3 units. All operated as expected with 5V serial signal interface. At 3.3V serial interface all 3 units shown a 4.2 V at pins 3V, TXD RXD in idle. The unit was powered via USB connector and I measured 5Vcc at 5V pad and 4.2V at 3V pad The CP2102 datasheet ( https://www.silabs.com/Support%20Documents/TechnicalDocs/CP2102-9.pdf ) states " Regulator Output Voltage, Typical 3.3V" The 4.2V I measured is out of specs ! To keep the signals in the 3,3V range I disconnected the RXD LED pull-up and placed a 100k pull-down resistor to RXD and placed a 1K/3K3 resistor attenuator on TXD, Next time possibly I will buy http://www.banggood.com/CH340G-USB-To-TTL-Auto-Converter-Adapter-STC-Brush-Module-p-1065230.html that shows a 3V3/5V switch

    Комментарии (2)
    Показать оригинал
  • 24/12/2015

    I tested all three of them, and they work like a charm! The only downside is that I got straight headers with mine... If you purchase this item to program Arduinos, be careful, as the DTR pin can not be directly connected to the RST pin on the Arduino. The solution: Take a 0.1µF ceramic capacitor (104 marking), and put one pin on the DTR pin of this adapter, and the other pin on the RST of your Arduino. The auto reset should work fine now! I also found out the bottom LED is not the power LED (there is none), but the USB suspend line. If the LED is OFF, it means that the adapter is sleeping. This means, it will consume less power than when it's awake. This feature is great too! The adapter will become active again when you try to communicate with it. This means that the LED will come on again. Again, pleased with the product, and I will buy again from Banggood!

    Комментарии (1)
    Показать оригинал
Show:

    Общий 0 страницы

    Перейти на страницу

    recommendation for you
    • US$2.15
    • US$1.99
    • US$7.99
    • US$17.99
    • US$6.99
    • US$10.99
    • US$9.99
    • US$15.99
    • US$7.99
    • US$17.99
    • US$8.99
    • US$7.99
    • US$7.99
    • US$2.19
    • US$7.99
    • US$7.00
    • US$2.99
    • US$14.99