Отзывы покупателей

4.9 из 5
Написать отзыв
  • Все отзывы (31)
  • Образ (1)
  • Видео (0)
  • Все звезды
    • Все звезды(31)
    • 5 Звезда(28)
    • 4 Звезда(3)
    • 3 Звезда(0)
    • 2 Звезда(0)
    • 1 Звезда(0)
Сортировать по:
оценке
  • оценке
  • полезности
  • дате
  • 2018-06-06 02:15:28

    Good condition arrived in safe and all parts is ok! Good value/quality ratio. Thank you! :)

    Комментарии
  • Jiří
    CZ
    2020-10-26 07:29:56

    OK

    Комментарии
  • baldax
    IT
    2020-08-08 01:08:18

    Excellent component, easy to use with Arduino.

    Комментарии
  • 2020-02-04 12:54:20

    Can't go wrong with these

    Комментарии
  • Ferdie
    SA
    2020-01-22 08:40:59

    As advertized, good quality, timely delivery. I can endorse this item.

    Комментарии
  • 2018-01-30 19:54:54

    The encoder is OK, but the switch is NOT brought out to any pins, which means soldering, no matter what you do. Since the 'C' pin is directly connected to the GND pin, you can cut the trace on the back between the two pins, and wire one side of the switch to the old GND pin, and then wire the other side of the switch to either 'C' (the new GND pin) or to VCC. Normally you'll want the switch to GND as most micros have internal pull-up resistors, and it's less to wire in later. I've added a schematic

    Комментарии (1)
  • MartinB
    CZ
    2018-11-05 16:03:18

    You need to plug the pins and you can use the rotator. Beware! The button can not be used, it is connected to GND. If you would like to use the button, you need to make changes to the printed link as someone has already written. Turning the rotator is a little harder, but it can be useful!

    Комментарии
  • S57SU
    SI
    2018-04-10 17:51:14

    endocer works fine but key is not connected at all, see PCB bottom side. Further down you can find pics how to correct this mistake. Hopefully the factory will correct PCB drawing b4 next fabrication

    Комментарии
  • Jonee
    US
    2018-02-12 07:50:25

    As others have commented, the momentary contact switch is not connected to any of the pins on this board. The encoder board comes with nut and washer and so can be mounted either with standoffs or the encoder shaft. Solid made board otherwise.

    Комментарии
  • bilbo
    US
    2018-01-24 16:22:13

    This is a nicely built module The encoder itself is mechanical with a definite "click" between each step. A useful item for toggling through a menu, etc.

    Комментарии
Show:

    Go to page

    Go

    Рекомендуем

    recommendation for you
    • US$6.08
    • US$22.75
    • US$7.99
    • US$10.39
    • US$6.49
    • US$10.08
    • US$5.54
    • US$1.83
    • US$4.36
    • US$11.99
    • US$1.99
    • US$12.99
    • US$17.08
    • US$9.99
    • US$7.99
    • US$26.49
    • US$30.99
    • US$132.86