Très bon combo pas chère. Esc suffisant pour des moteurs 1103. Seul truc qui manques des uart pour la télémétrie et smart audio

Très bon combo pas chère. Esc suffisant pour des moteurs 1103. Seul truc qui manques des uart pour la télémétrie et smart audio

Très bon combo pas chère. Esc suffisant pour des moteurs 1103. Seul truc qui manques des uart pour la télémétrie et smart audio

I built this with a 65 mm Whoop frame with a 0603 17000KV, a PH 02 pigtail. It flies so smooth with a dying 1S Lipo. I know this could be a monster 65mm Whoop when I got a new battery.

I built this with a 65 mm Whoop frame with a 0603 17000KV, a PH 02 pigtail. It flies so smooth with a dying 1S Lipo. I know this could be a monster 65mm Whoop when I got a new battery.

I built this with a 65 mm Whoop frame with a 0603 17000KV, a PH 02 pigtail. It flies so smooth with a dying 1S Lipo. I know this could be a monster 65mm Whoop when I got a new battery.

The TeenyF4 Pro Flytower comes with 2M standoffs, screws and nuts. I also used tiny rubber rings (and longer screws) to soft mount the flytower onto a SPC 95EP frame. Soldering the motors to the 4 in 1 ESC was easy. The 5A ESC can handle motors as large as 1102. I'm using smaller Happymodel 0802 19000KV motors (1S). A battery connector is not included with the flytower. I chose a JST-PH2 battery connector and 3.8V 450 mAh LiPos. The solder pads on the flight control board are very small and require a steady hand. A small tipped soldering iron is helpful. I've attached a 25mw AIO Cam/VTX w/ OSD and a small FrSky D8 receiver. After binding the receiver to the TX and configuring basic settings in Betaflight, the quadcopter flew surprisingly well. Updating the firmware and configuring Betaflight (PIDs and rates) is the next step.The green propellers shown in the picture have been discontinued. Red & black Eachine 3 blade propellers are current. All of the parts mentioned here are available from Banggood. I would recommend the TeenyF4 Pro to anyone interested in building a compact lightweight micro.

The TeenyF4 Pro Flytower comes with 2M standoffs, screws and nuts. I also used tiny rubber rings (and longer screws) to soft mount the flytower onto a SPC 95EP frame. Soldering the motors to the 4 in 1 ESC was easy. The 5A ESC can handle motors as large as 1102. I'm using smaller Happymodel 0802 19000KV motors (1S). A battery connector is not included with the flytower. I chose a JST-PH2 battery connector and 3.8V 450 mAh LiPos. The solder pads on the flight control board are very small and require a steady hand. A small tipped soldering iron is helpful. I've attached a 25mw AIO Cam/VTX w/ OSD and a small FrSky D8 receiver. After binding the receiver to the TX and configuring basic settings in Betaflight, the quadcopter flew surprisingly well. Updating the firmware and configuring Betaflight (PIDs and rates) is the next step.The green propellers shown in the picture have been discontinued. Red & black Eachine 3 blade propellers are current. All of the parts mentioned here are available from Banggood. I would recommend the TeenyF4 Pro to anyone interested in building a compact lightweight micro.

The TeenyF4 Pro Flytower comes with 2M standoffs, screws and nuts. I also used tiny rubber rings (and longer screws) to soft mount the flytower onto a SPC 95EP frame. Soldering the motors to the 4 in 1 ESC was easy. The 5A ESC can handle motors as large as 1102. I'm using smaller Happymodel 0802 19000KV motors (1S). A battery connector is not included with the flytower. I chose a JST-PH2 battery connector and 3.8V 450 mAh LiPos. The solder pads on the flight control board are very small and require a steady hand. A small tipped soldering iron is helpful. I've attached a 25mw AIO Cam/VTX w/ OSD and a small FrSky D8 receiver. After binding the receiver to the TX and configuring basic settings in Betaflight, the quadcopter flew surprisingly well. Updating the firmware and configuring Betaflight (PIDs and rates) is the next step.The green propellers shown in the picture have been discontinued. Red & black Eachine 3 blade propellers are current. All of the parts mentioned here are available from Banggood. I would recommend the TeenyF4 Pro to anyone interested in building a compact lightweight micro.

using this in a toothpick style build with 0802 16000kv motors. work great together.

using this in a toothpick style build with 0802 16000kv motors. work great together.

using this in a toothpick style build with 0802 16000kv motors. work great together.

perfect

perfect

perfect

Отлично!

perfect!

Отлично!

Это дешево и хорошего качества.

安くて品質いいですよ

Это дешево и хорошего качества.

Very good stack. Works as expected on 1s and 2s

Very good stack. Works as expected on 1s and 2s

Very good stack. Works as expected on 1s and 2s

good and simple

good and simple

good and simple

супер микро контреллер, ещё и с регулем!

супер микро контреллер, ещё и с регулем!

супер микро контреллер, ещё и с регулем!