Отзывы покупателей

Написать отзыв
  • Все отзывы (435)
  • Образ (68)
  • Видео (0)
  • Все звезды
    • Все звезды(435)
    • 5 Звезда(427)
    • 4 Звезда(7)
    • 3 Звезда(1)
    • 2 Звезда(0)
    • 1 Звезда(0)
Сортировать по:
оценке
  • оценке
  • полезности
  • дате
Отзывы только из вашей страны (Russian Federation)
|
Показать оригинал

Часть обзора переведена автоматически.

  • 08/05/2017

    A propeller cut one of the antennas on my RX, so needed replacements. Price is low and quality looks OK, have not tried them yet. The unshielded part of the antenna is not protected by an extra plastic tube like on the original antennas on my RX, but should not be a problem.

    Комментарии
    Показать оригинал
  • 11/07/2018

    Not ipex or pigtail you must be solder directly receiver.

    Комментарии
    Показать оригинал
  • 04/01/2018

    These are great antennas they'll restore your RX to full range after you put the original ones into your props. Very challenging to solder though my picture is magnified 50x and the joins are good... You'll need a bloody small soldering tip and a couple of drinks to steady your hand and you'll be good to go! I think I'll get receivers with the plug type connectors from now on.

    Комментарии
    Показать оригинал
  • 29/07/2021

    Хорошая замена антенны 2,4 ГГц. Солдат на месте и уходи. Я бы купил агин.

    Комментарии
    Показать оригинал
  • 07/08/2017

    Elle m'ont servit a remplacer les antennes de mon récepteur XSR. Elles sont un peu plus longues mais ça n'est pas dérangeant et elles sont surtout super faciles à souder. Aucun soucis avec. :-)

    Комментарии
    Показать оригинал
  • 26/02/2018

    I used these to repair some damaged antennas on my Turnigy receivers. Worked just as well as the originals. recommended.

    Комментарии
    Показать оригинал
  • 17/04/2018

    Just what I was looking for. These are the shielded antenna wires but instead of the more expensive braided shielding, this is the cheaper foil shielded antenna replacement. It DOES NOT have and plug on the end (like FrSky uses) instead I soldered the center cable to the existing antenna location, then grounded the shielding to any ground point on the PCB (used cont. tester to locate a ground point) When soldering the foil, use a dab of flux, tin the surface first, and only touch the tip of iron a brief time to avoid melting the plastic tubing. Worked just as I wanted to extend the working portion of the antenna past carbon fiber frame.

    Комментарии
    Показать оригинал
  • 23/06/2017

    Это очень хороший вариант! Дёшево!

    Комментарии
    Показать оригинал
  • 26/04/2017

    got these for the XSR, will see how they fair in longer range tests but seem good!

    Комментарии (1)
    Показать оригинал
  • 22/04/2017

    GOOD

    Комментарии
    Показать оригинал
Show:

    Общий 0 страницы

    Перейти на страницу

    Рекомендуем

    recommendation for you
    • US$109.99
    • US$19.99
    • US$53.99
    • US$67.99
    • US$25.99
    • US$10.99
    • US$12.99
    • US$22.99
    • US$13.99
    • US$2.99
    • US$14.99
    • US$11.99
    • US$10.99
    • US$23.99
    • US$34.99
    • US$31.99
    • US$239.99
    • US$7.99