Отзывы покупателей

Написать отзыв
  • Все отзывы (107)
  • Образ (9)
  • Видео (0)
  • Все звезды
    • Все звезды(107)
    • 5 Звезда(92)
    • 4 Звезда(3)
    • 3 Звезда(3)
    • 2 Звезда(4)
    • 1 Звезда(5)
Сортировать по:
оценке
  • оценке
  • полезности
  • дате
Отзывы только из вашей страны (Russian Federation)
|
Показать оригинал

Часть обзора переведена автоматически.

  • 25/05/2017

    good but missing cables

    Комментарии
    Показать оригинал
  • 09/05/2017

    My tiny-whoop has quickly become my absolute favorite quadcopter. This started life as a stock Eachine E010s (see other video for my original reviews and mods), but now it's a streamlined, speed-machine which can hang with the very best of whoops. These new Racerstar motors, paired with kingkong tri-blades allow for such a high level amount of control. My taranis, with M9 gimbals, mean that this little whoop feels like it's a part of you when you fly it. I'm in love, and want to preach this BamRamirez Ultimate Whoop gospel. This brain comes in handy if you happen to burn out a FET or crash too much and damage your original one. see my full review here: https://youtu.be/wqqyvmBjdEs

    Комментарии
    Показать оригинал
  • 22/10/2017

    I installed this board on my JJRC H36 the day it arrived in my mail. The quality is pretty good for such a small board. I have a Flysky version and it binds on on AFHDS protocol instead of the AFHDS2A. The only issue I experienced was in the bind process. Even though it was bound to my radio the very first time the radio did not show the confirmation. Only after watching a video on YouTube I found out that it was already bound. The Cleanflight onboard was pretty old and even the configurator forced me to update it. I first updated it to Cleanflight Spracing F3 3.1.1 and then installed Betaflight Spracing F3 3.1.1. Works perfectly fine for me. Check out the flight video: https://youtu.be/268UXmGB9mE

    Комментарии (2)
    Показать оригинал
  • 29/09/2018

    Factory FX is Cleanflight 1.13.0 from 2016m so I installed latest Beteflight FW. I'm using a DX6i, I tried to use a UART for serial RX and SPEKTRUM2048, but it did not work. It works without UART, simply set receiver on RX PPM and set spektrum_sat_bind to 9.

    Комментарии
    Показать оригинал
  • 16/12/2017

    Connection s are not attached as in picture. You have to solder both the cammera connection and the power leads. The cammera connector shown IS NOT PROVIDED. Not so easy as the place to solder them is small and with other connections nearby so yuu have to ve very careful. The picture should represent what you get

    Комментарии
    Показать оригинал
  • 05/01/2018

    Awesome! great to flight with your favorite flight transmitter. it have a 5v for powered your camera. fun to flight acro get pretty crazy speed in the house.

    Комментарии
    Показать оригинал
  • 29/07/2017

    I had a problem with my order and they went above and beyond to fix it for me. Thank you

    Комментарии
    Показать оригинал
  • 16/09/2017

    updated to last BF firmware. It rocks. you can buy

    Комментарии
    Показать оригинал
  • 03/09/2017

    I had one with a problem and it was solved immediately by customer sevice. Great deal

    Комментарии
    Показать оригинал
  • 07/06/2017

    Para solamente configurar parametros sin tener que flashear yo busqué e instalé una version antigua de Clanflight puesto que la ultima version no lo soportaba. Despues, desde esa version antigua de clanflight flashee la placa a la ultima version del firmware de la placa.Yo lo hize de la siguiente manera: Preparé la ultima version de Cleanflight 2.0.3 en la seccion de Firmware flasher seleccioné el modelo spracingf3 y la ultima version del firmware,activé "no reboot secuence" "full chip erase" y "manual baud rate a 256000" Tambien en la zona de arriba , a la derecha debajo de "Puerto" puse 256000. Una vez hecho esto, pinché en el boton de abajo "load firmware on line" con un pequeño destornillador puentee los pines "boot" de la placa y le conecté el usb, parpadea una sola vez un led azul y entonces le doy "flash firmware" y ya está. Curiosamente si quieres volver a flashear o pasar a Betaflight, ya no hace falta puentear boot en la placa.

    Комментарии
    Показать оригинал
Show:

    Общий 0 страницы

    Перейти на страницу

    Рекомендуем

    recommendation for you
    • US$21.99
    • US$42.99
    • US$21.99
    • US$69.99
    • US$7.99
    • US$89.99
    • US$29.99
    • US$239.99
    • US$139.99
    • US$67.99
    • US$569.99
    • US$110.99
    • US$299.99
    • US$199.99
    • US$145.99
    • US$65.99
    • US$49.99
    • US$379.00