Отзывы покупателей

Написать отзыв
  • Все отзывы (1363)
  • Образ (180)
  • Видео (8)
  • Все звезды
    • Все звезды(1363)
    • 5 Звезда(1246)
    • 4 Звезда(72)
    • 3 Звезда(24)
    • 2 Звезда(8)
    • 1 Звезда(13)
Сортировать по:
оценке
  • оценке
  • полезности
  • дате
Отзывы только из вашей страны (Russian Federation)
|
Показать оригинал

Часть обзора переведена автоматически.

  • 09/11/2016

    Package is full, but the instruction document is not the good one for the colorful led version. I upload a picture with the correct resistor value !

    Комментарии (3)
    Показать оригинал
  • 11/11/2017

    All components included easy to solder, good for beginners bcps are labeled for most components 10k (r1,r3,r5 = brn,blk,org,gold) resistors, transistors, capacitors, switch and power connectors are clearly marked 2.2k (red,red,red,gold) goes in r7 on pcb 'A' all others resistors are the 1k (r2, r4, r6 = brn,blk,red,gold) the r7 2.2k resistor runs the top led my kit included one extra led, and had one bad led tree stands 5.5x2.5x2.5 when completed very low power draw, 0.05a

    Комментарии (2)
    Показать оригинал
  • 15/11/2015

    Fine kit. Everything was in the package (I even got one extra LED) Instructions are fine, but the delivered resistors does not match the instructions. Just follow the instructions, and use correct resistors (see below)) The correct resistors: R1, R3, R5, R7: 10 kOhm (Note: R7 is only on board CTR-30A) R2: 2,2 kOhm R4: 1 KOhm R6: 33 Ohm (39 Ohm works fine) Have fun.

    Комментарии (1)
    Показать оригинал
  • Aerotec
    GB
    13/12/2016

    Having no experience of electrical circuits I was unsure what to do when this arrived. The download instructions aren't that clear so here are my tips for assembling the multi colour LED version with white LEDs: View a PDF with assembly details here (Credit to the reviewer pages back who posted this): http://www.haoyuelectronics.com/Attachment/CTR-30C/CTR-30C%20Flashing%20Christmas%20Tree%20Instruction.pdf Link with images is: http://www.haoyuelectronics.com/Attachment/CTR-30C/ CTR-30A is one tree PCB CTR-30B is the other one CTR-30C is the base Resistors: These can be fitted in either direction and are: 6 x 1k: Colour bands Gold/Red/Black/Brown 6 x 10k: Colour Bands Gold/Orange/Black/Brown 1 x 2.2k: Colour Band Gold/Red/Red/Red Locate where these go via the pdf and insert in to the relevant location R1, R2 etc... The single 2.2k goes on R7 on CTR-30A. Transistor (With the 3 legs) Must be fitted the right way but the PCB shows the orientation. All are the same spec so use any of them. Capacitor Must be fitted the right way. Longer leg is (+) Positive. And negative side is printed on the casing. All the same spec so fit where required. LEDs Must be fitted the right way. Longer leg is (+). Positive terminal is the lower location where the letter is such as D1, D2 etc. Solder in place with enough length to bend to point out the way. Solder the tree segments together. When you fit the soldered tree to the base I recommend installing and power up to test before soldering in as you can have a (+) against a (+) as per the instructions but it can still be 90 degrees out. I did this and it was a pain to unsolder as I didn't have a solder sucker. It all went together and worked great once I had realigned the tree to the base and works great off USB power.

    Комментарии
    Показать оригинал
  • 23/12/2020

    Это так красиво, и довольно легко сделать. Но нет никакого руководства, написанного на бумаге, и загруженное руководство с ссылки не является правильным. Если вы сделаете это, резисторы типа этого: Часть A R1=10k R2=1k R3=10k R4=1k R5=10k R6=1k R7=2.2k часть B R1=10 000 R2=1 000 R3=10 000 R4=1 000 R5=10 000 R6=1 000

    Комментарии
    Показать оригинал
  • 21/12/2017

    I have now purchased 5 of these kits. Lots of fun, once you figure out which resistors go where - See pictures. Youtube has some good videos on construction

    Комментарии (2)
    Показать оригинал
  • 13/11/2017

    Vor kurzem habe ich den Bausatzsatz erhalten und, nachdem ich eine Bauteiliste entsprechend der gelieferten Bauteile im Internet gefunden habe, zusamen gebaut. Nach dem Zusammenbau und dem harten Test, habe ich ein paar Bilder gemacht. Ausserdem habe die Bauteilliste beigelegt. Viel Spass beim Löten.

    Комментарии (2)
    Показать оригинал
  • 01/01/2021

    Хороший набор для обучения пайке. Качество печатных плат высокое: дорожки ровные без трещин, отверстия металлизированы. Собирается достаточно легко, в интернете есть текстовые и видео руководства. Собранная конструкция заработала сразу как при питании по USB кабелю, так и от трёх аккумуляторов АА. У меня оказался набор, в котором каждый светодиод светит поочерёдно тремя цветами: красным, зелёным и синим. В подставке есть четыре отверстия для крепления к основе, так что в будущем, возможно, я изготовлю защитный прозрачный корпус для этой ёлки. Ещё нужно добавить, что у этой конструкции очень маленькое потребление тока около 16 мА. Отличный подарок к Новому Году. Рекомендую.

    Комментарии
    Показать оригинал
  • 02/01/2018

    I have purchase 16 units in total as Xmas gift and everybody LOVE it.

    Комментарии (2)
    Показать оригинал
  • 06/02/2019

    Funny Christmas toy.

    Комментарии
    Показать оригинал
Show:

    Общий 0 страницы

    Перейти на страницу

    Рекомендуем

    recommendation for you
    • US$7.59
    • US$14.99
    • US$12.62
    • US$32.99
    • US$19.99
    • US$3.99
    • US$4.99
    • US$15.99
    • US$21.99
    • US$7.19
    • US$41.99
    • US$8.99
    • US$13.59
    • US$43.99
    • US$6.99
    • US$15.99
    • US$22.99
    • US$11.99