Доставить в United Kingdom , USD
Все категории

Отзывы покупателей

4.98 из 5
Написать отзыв
  • Все отзывы (42)
  • Образ (5)
  • Видео (0)
  • Все звезды
    • Все звезды(42)
    • 5 Звезда(41)
    • 4 Звезда(1)
    • 3 Звезда(0)
    • 2 Звезда(0)
    • 1 Звезда(0)
Сортировать по:
оценке
  • оценке
  • полезности
  • дате
    • Общая:
    • Цена:
    • Качество:
    • Внешность:

    2019-06-05 08:42:56

    Quick and easy install product as described v3 version totally happy with it

    Комментарии
    • Общая:
    • Цена:
    • Качество:
    • Внешность:

    2019-05-29 08:16:19

    very good

    Комментарии
    • Общая:
    • Цена:
    • Качество:
    • Внешность:

    2019-05-24 11:05:23

    Bltouch v3 has many solutions to install properly. A video by teachingtech in yt is the best and most comprehensive video on installation. Only down side it the need to bend the leads to make it fit in the motherboard box. Even with it bent, it may be a very tight fit. Aside from that, the wire length is long enough and easy to connect. I did not use the included isp-usb connector but the wire is nice to use if you need to extend the wire length of the LCD screen. Teaching tech also has a video if

    Комментарии
    • Общая:
    • Цена:
    • Качество:
    • Внешность:

    2019-05-05 09:46:24

    good product but it is the new series of BLTOUCH (v3 pre april). This V3 has little complicated settings, while buying research first about V3 bltouch(there are two v3 versions also pre april or after april)

    Комментарии
    • Общая:
    • Цена:
    • Качество:
    • Внешность:

    2019-04-11 09:11:55

    Works well on Ender 3, BUT if your control board has capacitor C7 installed (see photo) then you must remove it, or the very short duration Z-stop signal from BLTouch will not be detected and the extruder will just crash into the print bed when it auto-homes. This is a known issue with BLTouch and the latest Ender 3 control boards leave out C7. To refit the Ender 3/Pro cover and fan, you need to bend the four pins on the adapter PCB so that the 4-way header from BLTouch is horizontal. Versions of

    Комментарии
    • Общая:
    • Цена:
    • Качество:
    • Внешность:

    2019-05-22 19:15:17

    It is works fine with ender3 pro.

    Комментарии
    • Общая:
    • Цена:
    • Качество:
    • Внешность:

    2019-07-20 09:42:18

    Product was well packaged...Shipping was very quick. Installation was easy. Very happy with product

    Комментарии
    • Общая:
    • Цена:
    • Качество:
    • Внешность:

    2019-07-16 13:25:07

    perfect

    Комментарии
  1 2 3 4 5 6  

Рекомендуем

Онлайн-консультант
Опрос удовлетворенности

Скачать приложение, чтобы получить эксклюзивный 10% off купон